FRESH
Hacker News
Hacker News Hacker News1. Frequency mixer, used for heterodyning, important in radio, so I hear. https://en.wikipedia.org/wiki/Frequency_mixer
2. Log converter, where the output voltage is proportional to the logarithm of the input voltage. https://electronics.stackexchange.com/questions/374440/log-c...
3. Diode ring, which provides variable gain, used in analog compressors like the Neve 33609 (I have a clone of the 33609, and I’m very fond of it)
Think about this: if you have a nonlinear device like a diode, then the dynamic resistance changes depending on the operating point. If you modulate the operating point, you’re modulating the dynamic resistance.
Diode half-wave rectifier https://www.circuitlab.com/editor/4da864/
Diode full-wave (bridge) rectifier https://www.circuitlab.com/editor/f6ex5x/
Diode turn-off time https://www.circuitlab.com/editor/fwr26m/
LED with resistor biasing https://www.circuitlab.com/editor/z79rqm/
Zener diode voltage reference https://www.circuitlab.com/editor/7f3ndq/
Charge Pump Voltage Doubler https://www.circuitlab.com/editor/24t6h3ypc4e5/
Diode Cascade Voltage Multiplier https://www.circuitlab.com/editor/mh9d8k/
(note: I wrote the simulation engine)
but here's where it matters: when your hardware breaks in weird ways or your IoT thing has power issues, and you're stuck debugging with vendors. I've watched founders burn weeks because they couldn't speak the language.
maybe the real lesson is knowing when to stay in your lane vs when to dive one layer deeper. most of the time you don't need this. but when you do, not knowing costs you time and money.
> This topic seems to be broadly misunderstood. It is 100% verified fact by both myself and others (including university researchers) that diode strings can produce more heat (or watt-hours, BTU) from a given solar panel than a bare resistance element.
https://en.wikipedia.org/wiki/Baker_clamp
Flyback diode:
https://en.wikipedia.org/wiki/Flyback_diode
A diode can switch off an AC source when a battery is present: see second circuit in accepted answer, introduced by, "Alternatively, you can probably get away with just using some schottky diodes:"
https://electronics.stackexchange.com/questions/71753/whats-...
Also, diodes can be used to provide a controlled discharge path for capacitors when a device is turned off.
The circuit in this EE StackExchange question shows it:
https://electronics.stackexchange.com/questions/471285/capac...
It has one RC constant when charging and a different RC constant when discharging through the diode.
Why would you want to charge a capacitor slowly when power is applied to the device, but discharge it fast when power is cut? There are various applications for that.
For instance, circuits that control some timed behavior, like holding a CPU chip in a reset state at start up while power stabilizes, and then releasing it. You want that circuit to reset itself quickly if power is lost.
Analog circuits have things like that in them: for instance circuits that mute an audio amplifier on power up for a bunch of milliseconds until a capacitor charges. If the power is cycled, you want that timer to reset itself.
Another application: Log amp: https://en.wikipedia.org/wiki/Log_amplifier
This exploits the diode's characteristic V-I exponential curve in amplifier feedback to produce output proportional to the logarithm of the input.
AJH Synth Sonic V Diode Ladder Filter. (IMHO AJH make the best eurorack filters out there..)
I always thought RTL was pretty nifty, and it was used in a lot of early computers. I think it's a lot less fussy of component values than the earlier RTL.
Any good suggestions on resources talking about building complex digital logic out of something more suitable?
How completely unintuitive.
